 |
Due
to the unique material characteristics of polyethylene,
heat fusion allows successful joining of pipe and
fittings into a single leak-free system with no
connections to corrode or loosen.“The basic principle of heat fusion (in this case butt, saddle or socket fusion) is to heat and melt the joint surfaces and force the melted surfaces together, which causes the materials to mix and fuse into a monolithic joint.” AWWA PE Pipe - Design and Installation, Manual of Water Supply Practices M55.
Central Plastics has been actively involved in the research and development of innovative joining methods for polyethylene piping systems since the early 1960’s. Recognized as an industry leader in the world of manufactured Polyethylene (PE) fittings; Central Plastics offers our customers the broadest and most complete line of Butt, Saddle, and Socket fusion fittings. All designed, manufactured and tested in Shawnee, Oklahoma. under ISO 9001 standards and serviced by an experienced staff of the most knowledgeable and customer friendly professionals you could hope to find.
Central Plastics Catalog
(108 pages, allow time to load)
Bringing unrivaled knowledge, experience and
manufacturing capabilities to industries throughout the
world, Central Plastics delivers innovative and cost
effective pipe joining solutions right to your door
step. Servicing the polyethylene fitting needs in
natural gas, potable water, municipal wastewater, oil &
gas gathering, mining, landfill, telecommunications,
geothermal, irrigation and other industries; Central
Plastics is helping to ensure that your conventional
fusion job is done right - the first time.
With an extensive and state of the art in-house testing facility, Central Plastics performs the following tests on all of our Butt, Saddle, and Socket fittings.
1. ASTM D 1599 - Minimum Hydraulic Burst Pressure Test.
2. ASTM D 1598 -Sustained Pressure Test Results.
3. ASTM D638 Tensile Strength Test.
4. PE3408/PE4710 Fittings are tested to the requirements of AWWA C906 (where appli-cable)
5. PE3408/PE4710 FM Tested and Approved (where applicable)
Conventional Fusion: Butt Fusion Fittings
Central’s Molded PE2406/PE2708 Butt fittings are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 and are sized for use with pipe conforming to ASTM D2513 and with Butt fittings conforming to ASTM D3261. Central’s PE2406/PE2708 Butt fittings are molded from a virgin yellow medium density resin in accordance with the material specifications listed in ASTM D3350 with a designation of PE2406/PE2708. All Central Plastics PE2406/PE2708 Butt Fittings are compatible for heat fusion with any pipe or fitting manufactured from a like or similar resin. Central’s PE2406/PE2708 fittings have been qualified for fusion using PPI generic fusion procedures.
Central’s Molded PE3408/PE4710 Butt fittings are manufactured and tested to the requirements of ASTM D2513, ASTM D3261, and ANSI/AWWA C906 for use with outside diameter controlled pipe and fittings conforming to ASTM D2513, ASTM D3035, ASTM F-714. Central’s PE3408/PE4710 Butt fittings are molded from an NSF listed resin in accordance with the material specifications listed in ASTM D3350 with a designation of PE3408/PE4710. Central Plastics PE3408/PE4710 Butt fittings are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 (where applicable) and are compatible for heat fusion with any pipe and or fitting manufactured from a like or similar resin. Central's PE3408/PE4710 fittings have been qualified for fusion using PPI generic fusion procedures.
Available Features:
Pressure rated for natural gas and potable water applications.
IAPMO Approved (where applicable).
CSA Approved (where applicable).
PE3408/PE4710 FM Approved (where applicable).
PE3408/PE4710 fittings are tested to the requirements of AWWA C906.
Can be joined by butt, socket , electrofusion or mechanical methods.
Can be heat fused with all conventional and electrofusion fusion methods.
Conventional Fusion: Saddle Fusion Fittings
Central’s Molded PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 and are sized for use with pipe conforming to ASTM D2513 and with Butt fittings conforming to ASTM D3261 as applicable. Central’s PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles and Branch Saddles are molded from a virgin yellow medium density resin in accordance with the material specifications listed in ASTM D3350. All Central Plastic’s PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles and Branch Saddles are compatible for side-wall fusion with any pipe or fitting manufactured from a like or similar resin. Central's PE2406/PE2708 fittings have been qualified for fusion using PPI generic fusion procedures.
Central’s Molded PE3408/PE4710 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513, ASTM D3261 and ANSI/AWWA C906 for use with outside diameter controlled pipe and fittings conforming to ASTM D2513, ASTM D3035, ASTM F-714 and with Butt fittings conforming to ASTM D3261. Central’s PE3408/PE4710.
Side-Wall Tapping Tees, Service Saddles and Branch Saddles are molded from an NSF listed resin in accordance with the material specifications listed in ASTM D3350. All Central Plastic’s PE3408/PE4710 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 (where applicable) and are compatible for side-wall fusion with any pipe and or fitting manufactured from a like or similar resin. Central's PE3408/ PE4710 fittings have been qualified for fusion using PPI generic fusion procedures.
Available Features:
Pressure rated for natural gas and potable water applications.
IAPMO Approved (where applicable).
CSA Approved (where applicable).
PE3408/PE4710 are tested to the requirements of AWWA C906.
Can be heat fused to pipe wall using conventional side-wall fusion methods.
Outlets can be heat fused using conventional and electrofusion fusion methods.
New Page 1
With an extensive and state of the art in-house testing facility, Central Plastics performs the following tests on all of our Butt, Saddle, and Socket fittings.
1. ASTM D 1599 - Minimum Hydraulic Burst Pressure Test.
2. ASTM D 1598 -Sustained Pressure Test Results.
3. ASTM D638 Tensile Strength Test.
4. PE3408/PE4710 Fittings are tested to the requirements of AWWA C906 (where appli-cable)
5. PE3408/PE4710 FM Tested and Approved (where applicable)
Conventional Fusion: Butt Fusion Fittings
Central’s Molded PE2406/PE2708 Butt fittings are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 and are sized for use with pipe conforming to ASTM D2513 and with Butt fittings conforming to ASTM D3261. Central’s PE2406/PE2708 Butt fittings are molded from a virgin yellow medium density resin in accordance with the material specifications listed in ASTM D3350 with a designation of PE2406/PE2708. All Central Plastics PE2406/PE2708 Butt Fittings are compatible for heat fusion with any pipe or fitting manufactured from a like or similar resin. Central’s PE2406/PE2708 fittings have been qualified for fusion using PPI generic fusion procedures.
Central’s Molded PE3408/PE4710 Butt fittings are manufactured and tested to the requirements of ASTM D2513, ASTM D3261, and ANSI/AWWA C906 for use with outside diameter controlled pipe and fittings conforming to ASTM D2513, ASTM D3035, ASTM F-714. Central’s PE3408/PE4710 Butt fittings are molded from an NSF listed resin in accordance with the material specifications listed in ASTM D3350 with a designation of PE3408/PE4710. Central Plastics PE3408/PE4710 Butt fittings are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 (where applicable) and are compatible for heat fusion with any pipe and or fitting manufactured from a like or similar resin. Central's PE3408/PE4710 fittings have been qualified for fusion using PPI generic fusion procedures.
Available Features:
Pressure rated for natural gas and potable water applications.
IAPMO Approved (where applicable).
CSA Approved (where applicable).
PE3408/PE4710 FM Approved (where applicable).
PE3408/PE4710 fittings are tested to the requirements of AWWA C906.
Can be joined by butt, socket , electrofusion or mechanical methods.
Can be heat fused with all conventional and electrofusion fusion methods.
Conventional Fusion: Saddle Fusion Fittings
Central’s Molded PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 and are sized for use with pipe conforming to ASTM D2513 and with Butt fittings conforming to ASTM D3261 as applicable. Central’s PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles and Branch Saddles are molded from a virgin yellow medium density resin in accordance with the material specifications listed in ASTM D3350. All Central Plastic’s PE2406/PE2708 Side-Wall Tapping Tees, Service Saddles and Branch Saddles are compatible for side-wall fusion with any pipe or fitting manufactured from a like or similar resin. Central's PE2406/PE2708 fittings have been qualified for fusion using PPI generic fusion procedures.
Central’s Molded PE3408/PE4710 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513, ASTM D3261 and ANSI/AWWA C906 for use with outside diameter controlled pipe and fittings conforming to ASTM D2513, ASTM D3035, ASTM F-714 and with Butt fittings conforming to ASTM D3261. Central’s PE3408/PE4710.
Side-Wall Tapping Tees, Service Saddles and Branch Saddles are molded from an NSF listed resin in accordance with the material specifications listed in ASTM D3350. All Central Plastic’s PE3408/PE4710 Side-Wall Tapping Tees, Service Saddles, and Branch Saddles are manufactured and tested to the requirements of ASTM D2513 and ASTM D3261 (where applicable) and are compatible for side-wall fusion with any pipe and or fitting manufactured from a like or similar resin. Central's PE3408/ PE4710 fittings have been qualified for fusion using PPI generic fusion procedures.
Available Features:
Pressure rated for natural gas and potable water applications.
IAPMO Approved (where applicable).
CSA Approved (where applicable).
PE3408/PE4710 are tested to the requirements of AWWA C906.
Can be heat fused to pipe wall using conventional side-wall fusion methods.
Outlets can be heat fused using conventional and electrofusion fusion methods.
Casper Wyoming
Office and Warehouse
|
Farmington New Mexico
Office
|
Williston, North Dakota
Office
|